Today we’re going to walk through how to battery reconditioning, how to recondition a car battery at home. Keep reading! Saving money these days is very important, so why not starting by reconditioning your dead old battery?
This post has been created to allows peoples to save money on the battery by reconditioning them through a how-to battery reconditioning guide, so enjoy!
Important note: before starting any quid of battery reconditioning activities please takes these precautions, it may be dangerous for you! The liquid (called electrolyte) in lead-acid battery cells is very dangerous. It’s a mix of sulphuric acid and water, So be extra careful.
As that has been mentioned let’s jump to the subject of this article: how to battery reconditioning.
Learn How To Battery Reconditioning
How to recondition batteries depend tons on what type of battery it’s (Lead-acid, NiCad, Li-ion battery…) Correct knowledge of chemicals and proper handling is necessary for safe reconditioning of batteries, but don’t worry you can get this knowledge to recondition your batteries from the comfort of your home safely
, you will save money if you do it yourself!
Car Battery Reconditioning
How to Recondition a Car Battery at Home
If you’ve got magnesium sulfate (commonly called Epsom salt) with you’ll be able to easily recondition a car battery. Before we start let’s list types of Batteries that can be reconditioned
Types Of Batteries That Can Be Reconditioned
These batteries are rechargeable and becoming more popular, yet they’re costlier than the standard battery types. There are several ways to recondition a lithium-ion battery.
NiCad Rechargeable Batteries
Nickel-based batteries suffer from performance issues, primarily when recharged before they’re completely dead. To restore the performance, reconditioning is required, which needs putting high voltage on the battery terminals.
NiMH Rechargeable Batteries
The Nickel Metal Hydride is another rechargeable battery that’s better than the NiCad. To recondition a NiMH rechargeable battery, you would like to run deep charge cycles to regain the performance.
Lead Acid Car Batteries
These voltaic cell batteries don’t require tons of effort to recondition. You can complete off all of the cells with distilled water, which helps to apply a slow charge to the battery.
AGM and Gel Type Batteries
These batteries are safer than the lead-acid variety because nothing spills out if the casing cracks. The best thanks to reconditioning the gel battery are to completely discharge it then recharge it slowly.
To recondition a car battery you should follow this step-by-step guide on how to recondition a car battery at home.
Prepare the following materials first:
-Disposable rubber gloves
-Distilled water (1 gallon)
-Baking soda (powder)
-Battery terminal cleaner.
-Toothbrush (used or new)
After you have got the materials, you must follow this car battery reconditioning process step by step
Before preparing your battery for reconditioning, you need to wear your protective gear: apron, gloves, mask, and goggles. In addition, make a weak baking soda and water solution on the side to neutralize any sudden spills and splashes.
You need to remove the corrosion in the battery terminal. Prepare a paste-like solution of bicarbonate of soda and water with a ratio of 2:1. Grab your toothbrush and dip it into the paste-like solution, then rub it against the battery terminal to remove corrosion.
You can use wire wool or sandpaper grit if the corrosion is tough.
When you are done removing the corrosion, you measure the volt reading of the battery using a voltmeter. Check the connection of the cable to the battery terminal. The proper connection must be set like that: the red wire to the positive battery terminal and the black cable to the negative terminal.
Then read the voltage, for reading between 12.6v and higher, your battery is still in good condition.
Grab your flat head screwdriver and take away the battery caps. Place all battery caps in a temporary container to avoid losing them. Then, slowly lift your battery and pour out the old electrolyte solution within the bucket.
Do not throw the old battery acid solution. Neutralize it by pouring 500 grams of bicarbonate of soda powder into the bucket.
Prepare a baking soda and water solution with a ratio of 2:1 or 1:1. Mix well and fill each battery cell with the bicarbonate of soda solution. After filling up all cells, lock it back with the caps then shake it gently. Let the shaking last for about 30 seconds to a moment. After, unlock the caps and pour out the solution into the same bucket utilized in the previous step.
Next, replace the old battery electrolyte solution with Epsom salt solution with one molar concentration or by dissolving 120 grams in one liter of distilled water. Mix well until no solids are left undissolved. Then refill each cell then cover it with its cap.
The next step is to recharge the reconditioned battery at 12V / 2 amps slow charging mode. The charging usually takes around 24 to 36 hours. After charging, read the voltage of the battery employing a voltmeter. If the reading is around 12.42V to 12.6V, then your battery is in excellent condition already.
The last step is to subject your reconditioned car battery for a load test. You will need a battery load tester which can be bought from any hardware store.
To pass the load test, it must successfully maintain 9.6V for 15 seconds at half the CCA rating.
It’s all for this guide on how to battery reconditioning, don’t hesitate to try to do it yourself (with all precaution of course) to save money!